How to add segment cards to a live podcast

A rundown on paper is a rundown only you can see. Put each segment on a band across the frame and the whole room knows where the show is — including the guest who cannot see your notes.

4 steps ~6 minIntermediate Updated September 2026

How do you show segments on a live podcast?

Use the band layout — a strip across the frame naming the current segment and counting it down, with the camera area left clear. Set each card to switch at zero and the run of show advances by itself.

You set it up here

It lands here — the real overlay

Manual
LIVE👁 1,248

A band keeps your guests on screen. At zero it hands off to the next segment by itself.

What you’ll build

A run of show that plays itself: named segments, each on a clock, handing off at zero.

Step by step

  1. 1

    Add your Kloot overlay to OBS once

    One source for the whole show, however many segments it has.

  2. 2

    Make a card per segment

    Name each one and say what is next. Keep the names short — a band is a strip, not a slide.

  3. 3

    Use the band layout

    It sits across the frame instead of over it, so your guests stay visible the whole time.

  4. 4

    Give each one a clock and chain them

    Set the length, then tell each card to switch to the next at zero. Press the first one when you start.

    Leave the last card set to hide at zero, so the show ends rather than looping.

How screens run a whole stream

One key each carries the show’s arc — Starting Soon before you go live, BRB at the break, Ending at the close. Here’s the loop, and what each side sees.

  1. Before you go live· step 1

    Fire Starting Soon, then start the stream

    Press the Starting Soon key before you hit Go Live in OBS. The scene covers the whole canvas — your title, subtitle, and an optional countdown — so early arrivals see a show warming up, not your desktop or a frozen game menu.

    You: Press Starting Soon
    Overlay: Full-screen scene + countdown
    Viewers: Sees a show about to start
  2. Show time· step 2

    Press again — your scene was under it all along

    When you’re ready, the same key clears the screen. It fades out to reveal whatever OBS was already showing — game, cam, everything. You never built a second OBS scene and you never switched one.

    You: Press it again
    Overlay: Fades out to your scene
    Viewers: The stream opens clean
  3. Breaks· step 3

    Tap BRB — it covers everything instantly

    Door, food, bathroom: one tap (your phone deck works from the kitchen) and the BRB scene covers the entire canvas in one press — game, cam, and all. Set a countdown and it can even clear itself when you’re due back.

    You: Tap BRB from your phone
    Overlay: Covers the whole canvas
    Viewers: Knows you’ll be right back
  4. Wrap up· step 4

    Fire Ending to close the show

    The thanks-for-watching scene holds the screen while you say goodbyes, plug the socials, and send the raid. Screens are one-at-a-time, so firing Ending swaps out anything else — then you end the stream on a produced note.

    You: Press Ending
    Overlay: Thanks-for-watching scene
    Viewers: A clean outro, not a hard cut

When a full-screen scene earns its press

Every stream has moments the camera shouldn’t carry alone. These are the ones a screen covers:

The pre-stream ramp

When: You go live a few minutes before you’re actually ready — and viewers arrive early.

Why it works: A countdown screen turns dead air into anticipation. Notifications land, the room fills, and you finish your setup behind a scene that looks deliberate.

Breaks without dead air

When: Bathroom, door, food delivery — the two-minute step-away every stream has.

Why it works: One tap covers the room: game, cam, and desktop all at once. Nothing awkward stays on screen, and the countdown tells viewers exactly when to drift back.

Technical difficulties cover

When: The game crashes, audio drops, or a capture card picks tonight to die.

Why it works: A calm, branded “hang tight” screen beats a frozen frame. Viewers stay seated while you fix it, instead of assuming the stream is over.

The outro that holds raiders

When: End of stream — you’re saying goodbyes, plugging socials, sending or landing a raid.

Why it works: An ending scene keeps a produced frame on screen through the whole wind-down, so the last thing anyone sees is your brand, not a hard cut to offline.

The scenes you can run

Starting Soon, Be Right Back, Stream Ending — every preview below is the real full-screen renderer with its countdown ticking, scaled down, not a mockup.

⏳
Starting Soon
Hang tight — we’re live in a few
05:00

Starting Soon — the pre-show hold

The countdown that turns early arrivals into an audience.

Fire it, go live, and finish your coffee. The purple sweep, your title, and a live 05:00 countdown hold the screen while notifications bring people in — by zero you have a room, not an empty chat.

One key up before you go live
☕
Be Right Back
Grab a snack — back in five
05:00

Be Right Back — the break cover

One tap covers everything — game, cam, desktop — instantly.

“Back in five” with a ticking timer reads as a promise, not an absence. Set the countdown to auto-hide at 00:00 and the stream uncovers itself the moment you’re due back.

Can auto-hide itself at 00:00
👋
Thanks for Watching!
See you next time

Stream Ending — the goodbye

A produced close that holds the room through the wind-down.

“Thanks for watching” stays up while you wrap, plug tomorrow’s stream, and send the raid. Retext the subtitle to your schedule once and it’s one press at the end of every show.

One key closes the show

It covers everything — that’s the point

Your Kloot source sits on top of your OBS scene, so a screen hides the whole canvas in one press — and one more press reveals the game that was under it all along. No scene collection, no switching.

Your stream · OBS output
LIVE
Covers the full canvas — everything under it is hidden Your Kloot source sits on top of the scene, so no OBS scene switch is needed

Common mistakes to avoid

  • ✕Chaining the last card back to the first, which loops the rundown forever once the show ends.
  • ✕Writing a full sentence on a band. It is one line across the frame — name the segment and stop.

Frequently asked

What if a segment runs long?

Add time to the clock while it runs, or switch to the next card early. The chain does not cut off a good conversation.

Will the card cover my guests?

Not with the band layout — it is a strip across the frame, so the camera area stays clear.

Can I show the schedule too?

Yes — a schedule block lists your times and segments beside the card.

Which plan do I need?

The band layout and chaining are part of Creator ($15/mo). Free runs two screens with a countdown.

Set it up once.
Press it every stream.

One browser source. Every screen, every clock, one deck.

Free forever · Creator $99/yr or $15/mo · Pro $149/yr or $25/mo · Event Pass $9 for 3 days